液壓式啟閉機的故障原因及維修方法：
The causes and maintenance methods of hydraulic hoist malfunctions:
1.漏油以及油壓不穩：我們?cè)陂L(zhǎng)期使用啟閉機之后，安全制動裝置的各個油路部分以及閘閥油路間有大量的泄露現象，導致油壓下降，閘閥不能及時下降。這種現象的原因是因?yàn)橛械牟糠?a target="_blank">定送水  銅鼎銅鐘 淤泥固化設備 化糞池鋼模具 拱形骨架模具 保定代理記賬 保定道閘
螺絲松動，將螺絲擰緊即可消除故障。而油壓不穩是因?yàn)橐簤合到y(tǒng)中混入了空氣，我們應及時的排出空氣，或者將液壓調壓裝置線圈的電流濾波不好，線圈在上下震動，造成了油壓不穩，所以我們假裝電解電容器加強濾波即可解決該故障。
1. Oil leakage and unstable oil pressure: After long-term use of the hoist, there is a large amount of leakage in various oil circuits of the safety braking device and between the oil circuits of the gate valve, resulting in a decrease in oil pressure and the inability of the gate valve to drop in time. The reason for this phenomenon is that some screws are loose, and tightening the screws can eliminate the fault. The unstable oil pressure is due to the air mixed in the hydraulic system, so we should exhaust the air in time, or the current of the coil of the hydraulic pressure regulating device is not filtered well, and the coil vibrates up and down, causing the unstable oil pressure. Therefore, we can solve the problem by pretending to strengthen the filtering of the electrolytic capacitor.
2.殘壓過大。液壓式啟閉機的殘壓過大會導致制動器失去作用。其主要的原因是：1.電液調壓裝置的控制桿上的擋板距離噴嘴距離太小。2.溢流閥節孔太大。處理方法為：1.更換陽雕刻 手套生產設備 果樹反光膜 北京純水設備 保定網站制作 控制桿上擋板。2.將溢流閥節孔更換直徑小一些的節流孔。
2. Excessive residual pressure. Excessive residual pressure in hydraulic hoists can cause the brakes to lose their function. The main reason is that the distance between the baffle on the control rod of the electro-hydraulic pressure regulating device and the nozzle is too small. 2. The relief valve orifice is too large. The handling method is: 1. Replace the upper baffle of the control rod. 2. Replace the relief valve orifice with a smaller diameter orifice.
3.二級制動油壓值保壓性能故障：產生此故障的原因有：液壓式啟閉機的油路塊上的溢流閥內部有贓物卡住發信，使之關不嚴。單項節流截止閥開口太大，使油大量溢出。電磁換向閥內部有贓物，使得內泄漏太大。針對這一類的故障，我們可以先去下閥芯進行清理，去掉贓物，然后調節單項節流截止閥，使其開口盡量小，從而可以起到節流和補油的作用。
3. Secondary brake oil pressure retention performance fault: The reason for this fault is that there is dirt stuck inside the overflow valve on the oil circuit block of the hydraulic hoist, causing it to not close tightly. The opening of the single throttle stop valve is too large, causing a large amount of oil to overflow. There is dirt inside the electromagnetic directional valve, causing excessive internal leakage. For this kind of fault, we can first clean the valve core to remove the dirt, and then adjust the single throttle stop valve to make its opening as small as possible, so that it can play the role of throttling and oil supplement.